The Stroke panel menu's Edit Arrowheads… (stroke.arrowheads.edit) opens
Arrowheads.vectorcraft next to the preferences, creating it with one
example head when it is missing. Each symbol in the file is one head,
listed by name after the built-in heads in both arrowhead menus: it
points right, its registration point is the tip, and its height is drawn
as wide as the built-in heads. The file is read at startup and again
each time VectorCraft saves it; stroke.arrowheads.reload and
stroke.arrowheads.list read and list it.
Arrowhead gets a Custom variant, appended after the built-in names, that
carries the head's name and outline, so a document that uses one draws,
saves, reopens and exports it without the arrowheads file. stroke.set
takes {"custom": name} or the {"Custom": {name, path}} form that
document.inspect reports.
Part of #5421.
The width between two width points was a straight line, so a variable-width
stroke turned a corner at every width point.
- Each side of a width profile now follows a monotone cubic (Fritsch-Carlson)
through its points: no kink at a point, flat at a point wider or narrower
than both neighbours, never past either point of a span. Points on one line
stay on it and two-point tapers are unchanged; stacked points still step.
- widest() counts each span's wider left and wider right, since the two sides
needn't peak together.
- The outliner samples straight runs between width points closely enough to
follow the curve to the drawing tolerance (at most 64 samples per span and
4,096 per piece); straight spans get none.
- Tests that expected straight-line widths now expect the curve. The stroke
gradient coverage test uses Teardrop instead of Wave until #5964 is fixed.
A dashed stroke of a path with more than 1,024 path elements was outlined
whole in every frame after an edit. It is now outlined in and around the
view like a solid stroke. dash_kept runs the pattern along every segment
and keeps only the dashes and dots on the segments near the view, so they
sit where dashing the whole path puts them and the pixels are the same.
A pattern too fine to draw is still drawn solid, and that solid stroke is
cropped too.
At 1600 x 1200 the frame after one anchor moves takes 14 ms instead of
102 ms on a filled closed path of 50,000 anchors with 6 pt dashes and
4 pt gaps. anchor_bench now includes that document.
The check added for #1396 dropped the inner contour only when the path itself fell in the hole, which takes a stroke more than twice as wide as the shape. Between one and two times the size (a 30 pt ellipse with a 50 pt stroke), and on rectangles with round or bevel joins, the hole stayed.
An offset contour is now left out when no point of it lies half the weight from its subpath: it is then nowhere the edge of the stroke. Subpaths are judged one by one, and only when the stroke is at least as wide as the subpath's bounds, so ordinary strokes take the same single call as before.
A closed path stroked wider than it is came back as a ring, because the inner offset crossed the middle. When that outline no longer covers the path, the outer contour is kept so the stroke paints solid.
Each dash and dot of a profile stroke is as wide as the profile where it sits
along the whole path (before, dashes dropped the profile). Corners of profile
strokes take the stroke's miter (within the miter limit), round or bevel join on
the outer side and stay clean on the inner side, instead of a miter clamped at
4x; smooth points of curves bend round. Canvas, SVG/PDF outlines and Outline
Stroke share the geometry.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With alignDashes every run between corners and path ends holds a whole number of
periods, scaled to fit, with a dash (or dot) centred on each corner and on both
ends of an open path. It lives in the shared dash generator, so the canvas, SVG
and PDF export (as outlines) and Outline Stroke all draw it.
stroke.set: alignDashes and dashOffset edit the current pattern on their own, and
a new dash array keeps the offset and alignment it replaces. The Stroke panel
turns dashes on fitted to corners (or as last turned off), and its Exact/Fit
buttons send only the flag.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Hollow heads draw as rings (the open arrow as a chevron) and closed paths get
no heads. The stroke stops under each head, so it never shows through a hollow
head or past the tip; stroke.set {arrowAlign: "extend"|"tip"} chooses whether
the tip extends past the end point (default) or sits on it with the stroke
shortened. Line and heads share one paint box (a gradient runs on into the
head) and take the stroke and object opacity once, as one layer on the canvas
and one group in PDF. StrokeLayer.arrow_align is a new defaulted field, so
older files load unchanged. The Stroke panel's Align buttons get two generated
icons and are disabled when the stroke has no head.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The shared stroke geometry now has its own arc-length dash generator: a dash
of length 0 becomes a dot that a round cap paints as a disc and a projecting
cap as a square turned along the path (a butt cap paints nothing). Dashes
restart per subpath, join across the start of closed subpaths, and a pattern
too fine for the path draws solid. The canvas and raster export use it through
line_outline; the stroke.set params doc says how to get dots.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Arrowheads, width-profile outlines and dashed line outlines now come from
vectorcraft_effects::stroke (stroke_pieces, line_outline, width_outline), used by
the canvas and PDF export alike; the renderer caches profile outlines too. Width
profiles are a doc-level catalogue (WidthProfile::PRESETS, preset, preset_id,
id_of) shared by stroke.set and the Stroke panel; stroke.set rejects unknown
profile ids and its params doc lists the arrowhead names.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>